Frequency Conversion System Tension Testing Machine Hydraulic Clamp
Industry and functional characteristics:
1, metal tensile testing machine: metal material tensile strength,
small elongation, need to configure metal punctuation
extensiometer.
2, rubber tensile testing machine: rubber or elastomer elongation
is relatively large, need to be attached with a large punctuation
elongation device, at the same time the fixture design to consider
the characteristics of rubber, can not slip. Can be added with O -
ring fixture, tire industry fixture, etc.
3, plastic tensile testing machine: plastic tensile strength is
bigger than rubber, elongation is big or small, and often to test
three point bending test.
4, textile tensile testing machine: textile industry needs to test
fabric peeling, piercing, tearing, single yarn tensile test,
fixture and software is special.
5, paper tensile testing machine: paper needs to test tensile
strength, ring compressive strength, vertical pressure, flat
pressure, side pressure, peel strength, etc., more fixtures.
6, leather tensile testing machine: leather needs to test tensile
strength, tear strength, etc., the test item is relatively simple.
Four, according to the test materials: metal material fixture and
non-metal material fixture;
Five, according to the test temperature: normal temperature
fixture, high temperature fixture, low temperature fixture, high
and low temperature fixture;
Six, according to use: stretching fixture, compression fixture,
bending fixture, cutting fixture, stripping fixture, tearing
fixture, sealing fixture, bending and bending fixture;
Seven, according to the degree of automation: manual fixture,
pneumatic fixture, electric fixture, hydraulic fixture.
Control system:
1, frequency conversion system tensile testing machine: the use of
frequency conversion motor control system, stretching, compression
speed through the frequency conversion governor control.
2, servo system tensile testing machine: servo motor control
system, stretching, compression speed and displacement control is
more accurate. The servo motor system is a servo control system
with intelligent feedback operation, which can be used for speed
test, cycle test, programming test and so on.
3, other driving mode tensile testing machine: through the DC motor
control, the driving mode of tensile testing machine due to low
cost performance, has been gradually phased out.
Main Technical Parameter: Tensile Test Equipment:
| Max capacity | 5kg,10kg,25kg,50kg,100kg,250kg,500kg,1000kg,2000kg,5000kg(It is
optional.) can be setting |
| Induction method : | Precision load cell (sensor) |
| Max. Load Capacity : | 5000kg |
| Force Resolution/Accuracy: | ± 0.5% |
| Accuracy class : | 0.5 |
| Resolution: | 1/1,000,000 |
| Test width: | 400mm(Standard specifications special specifications can be
customized) |
| Test stroke : | Max.700 mm( included the fixture) |
| Stroke Resolution: | 0.01mm |
| Speed range: | 0.001-20inches/min |
| Reference Machine Dimension: | 800×530×1600mm (L*W*H) Support Customized |
| Power : | 1 phase 220V 50/60Hz |
| Packing | Standard Export plywood case |
| Force system | servo drives + Servo motor + precision ball screw drive |
| Control system | Mechanical transmission + TM2101 + Pulse Command and Control System
control |
| Measurement and Control System | TM2101 and control system; master controller uses the most advanced
32-bit ARM processor in the 21st century, the processing speed
of the Pentium-class common computer standards, compared to the
traditional 8 yuan SCM control system overall performance greatly
improved, faster operation, control accuracy higher |
Obtain data | The key components are used America's most stable and
ultra-precision 24 yuan AD,
sampling rate of up to 2000 times / sec, can capture the power of
instantaneous change process, the entire file, regardless of the
resolution of up to 1,000,000 indexing |
| Displacement Control: | Displacement encoder count with four frequency technology
So that the displacement of four times
the resolution can up to 0.0005mm |
| Safety devices: | 1. overload, emergency stop device 2. the upper and lower travel limit devices 3. the test is completed automatic shutdown device |
| Reference standard | ASTM D903, ASTM E8 CNS11888, JIS K6854, PSTC7 ASTM
D903,GB/T16491CNS-11888,JIS K6854, PSTC-7 ,ASTM E4,ASTM D828,ASTM
D882,ASTM,D1938,ASTM D 412 ,ISO 8339ASTM D3330,ASTM F88,ASTM
F904,ISO 37,JIS P8113,QB/T 2358,QB/T 1130 , ISO 527 ,ISO 178 and
other
standards.
|
Customer Support Services:
Ø Installation
Ø Training (Training customer employees)
Ø Calibration
Ø Preventative maintenance
Ø Replacement parts
Ø Assistance via phone or internet
Ø On-site diagnosis and repair/online diagnosis and repair
We will produce the machines according to confirmed PO
requirements. Offering photoes to show production process.
After finish production, offer photoes to customer to confirm again
with the machine. Then do own factory calibration or third party
calibration(as customer requirements). Check and test all the
details and then arrange packing.
Deliver the products in confirmed shipping time and inform
customer.
